AASHTO M 85-11
- Standard Specification for Portland Cement (ASTM Designation: C 150-11)
- standard by American Association of State and Highway Transporta
- Category: AASHTO
$50.00
$25.00
1. SCOPE
1.1. This specification covers ten types of portland cement as follows (Note 1):
1.1.1. Type I-For use when the special properties specified for any other type are not required;
1.1.2. Type IA-Air-entraining cement for the same uses as Type I, where air-entrainment is desired;
1.1.3. Type II-For general use, more especially when moderate sulfate resistance is desired;
1.1.4. Type IIA-Air-entraining cement for the same uses as Type II, where air-entrainment is desired;
1.1.5. Type II(MH)-For general use, more especially when moderate heat of hydration and moderatesulfate resistance are desired.
1.1.6. Type II(MH)A-Air-entraining cement for the same uses as Type II(MH), where air-entrainment isdesired.
1.1.7. Type III-For use when high early strength is desired;
1.1.8. Type IIIA-Air-entraining cement for the same use as Type III, where air-entrainment is desired;
1.1.9. Type IV-For use when low heat of hydration is desired; and
1.1.10. Type V-For use when high sulfate resistance is desired.
Note 1-Some cements are designated with a combined type classification, such as Type I/II,indicating that the cement meets the requirements of the indicated types and is being offered assuitable for use when either type is desired.
1.2. When both SI and inch-pound units are present, the SI units are the standard. The inch-pound unitsare approximations listed for information only.
1.3. The text of this standard references notes and footnotes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shall not be considered as requirementsof the standard.
1.1. This specification covers ten types of portland cement as follows (Note 1):
1.1.1. Type I-For use when the special properties specified for any other type are not required;
1.1.2. Type IA-Air-entraining cement for the same uses as Type I, where air-entrainment is desired;
1.1.3. Type II-For general use, more especially when moderate sulfate resistance is desired;
1.1.4. Type IIA-Air-entraining cement for the same uses as Type II, where air-entrainment is desired;
1.1.5. Type II(MH)-For general use, more especially when moderate heat of hydration and moderatesulfate resistance are desired.
1.1.6. Type II(MH)A-Air-entraining cement for the same uses as Type II(MH), where air-entrainment isdesired.
1.1.7. Type III-For use when high early strength is desired;
1.1.8. Type IIIA-Air-entraining cement for the same use as Type III, where air-entrainment is desired;
1.1.9. Type IV-For use when low heat of hydration is desired; and
1.1.10. Type V-For use when high sulfate resistance is desired.
Note 1-Some cements are designated with a combined type classification, such as Type I/II,indicating that the cement meets the requirements of the indicated types and is being offered assuitable for use when either type is desired.
1.2. When both SI and inch-pound units are present, the SI units are the standard. The inch-pound unitsare approximations listed for information only.
1.3. The text of this standard references notes and footnotes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shall not be considered as requirementsof the standard.
PDF
All of our standards document are available in PDF (Portable Document Format), an electronic, downloadable format.You will be able to download the file in your account downloads.
Multi-User Access
After purchasing, you have the ability to assign each license to a specific user.
Printable
At any time, you are permitted to make printed copies for your and your members' reference use.
